Skip to Content

Basement Floor Drain Backing Up

There are several causes of basement floor drain backing up. It can be caused by clogs in the main sewer line or a tree root. Hydro jetting, a process that is often used to clean basement floor drains, reduces the amount of liquid that can pass through the drain. Using a manual drain snake or a backwater valve may not be sufficient. For more information, visit the following links:

Hydro jetting reduces the amount of liquid that can pass through a basement floor drain

If your basement floor drain is backing up, you may not need to call a plumber immediately. If the clog is in an early stage, you can clean the drain yourself using hot water and vinegar. This combination is effective in breaking down soap deposits, but you should avoid using too much soap. In addition, make sure not to turn on the taps while cleaning.

Performing hydro jetting can resolve recurring clogs. While augers and plumbing snakes may work for minor clogs, they do not remove the buildup and can even push waste deeper into the plumbing system. For severe, recurring clogs, the hydro jetting method is required. The inside of pipes can become clogged with debris, grease, and mineral buildup.

Choosing hydro jetting as a solution to a basement floor drain backing up issue can save your money in the long run. Using this method, the plumber can clear a drain and get to the source of the problem without damaging the plumbing system. Hydro jetting is ideal for basement floor drains because it reduces the amount of liquid that can pass through the pipes.

Floor drains are not standard in all homes. Usually, they are located near the lowest area of the basement. They prevent flooding and are usually square or round with a grate on the cover. The size of these drains varies from six inches to a foot. If the floor drain is backed up due to tree roots, the hydro jetting method is the best solution. Otherwise, an auger can only remove a portion of the roots and cause the problem to return.

If the water is backed up, a composite drainage system can be installed. This system connects two or more fixture branches on the same level. It is made of different materials, such as quartz or metal. Quartz composite sinks, for example, have a natural look that is resistant to chipping and corrosion. Composite pipes also have a nut-and-sleeve connection, so you can connect multiple branches to a single vent.

Manual drain snake

A manual drain snake is a tool with a long, flexible metal cable and a rotatable handle. To use a manual drain snake, simply thread it through the basement floor drain’s P trap, then lower the snake into the drain. You can unwind the auger and rotate it at a steady speed until it hits a clog. Once you feel the snake begin to move freely, you can stop using the device and clean out the basement floor drain.

First, you’ll want to unplug the floor drain. Pull off the drain cap, which can pop off the floor drain easily with a putty knife or flathead screwdriver. Next, insert the drain snake into the main drain line. It will push the clog down the main line and back up the drain. A 25-inch snake will work best for cleaning out a clog and fixing standing water.

You can also try using a shop vac to clear the trap. The vac’s powerful suction will help remove debris from the floor drain’s interior. It will also help you clear out clogs in areas closer to the drain opening. A shop vac is available to rent at a hardware store. This way, you can save money and time while cleaning the basement floor drain. If you’re not confident enough to use a manual drain snake, you can try using a shop vac.

If you’re unable to reach the floor drain by hand, you can use an electric drain snake. This tool comes with a long cable and is controlled by a pedal. To use the electrical snake, plug it into an electrical outlet, and then insert the cable. Then, either use an automatic feed option or manually feed the cable into the drain. In both cases, you’ll need to place the cable at the drain hole and then feed it with the cord.

If you’re confident with your DIY skills, you can use a manual drain snake to clean the basement floor drain. This tool works by breaking up the clog and then dislodging it further down the pipe. A wire hanger is an excellent DIY tool for cleaning a basement floor drain. It also works well for removing a larger clog, but you need to be careful to avoid being too aggressive.

Main sewer line clogs

A basement floor drain clog may be the result of the main sewer line backing up. You may have a wash tub, laundry tub, or similar drain that backs up into the basement floor drain. While a plunger can clear out sediment from the trap, you might need a snake to clear the clog. In some cases, you may need to remove the trap entirely. If you can’t find the source of the clog, you may need to call a professional.

The main sewer line is the point where all the pipes in a house connect. A clogged main line causes the water in your basement floor drain to back up. If you notice water bubbling in other drains, including your kitchen sink, you may have a clogged main sewer line. Another symptom is a slow draining floor drain. You should check the drain regularly to make sure it is working properly.

The most common symptom of a backed-up main sewer line is a clogged floor drain. This clog can be caused by a number of reasons, including a surcharged drain system or a defective main line. If your basement floor drain backs up, it is likely due to a clogged main line in your house or a backed up trap. If your main sewer line clogs in your basement floor drain, you may need to call a plumber immediately.

There are a number of possible causes for a floor drain clog. One possible cause is tree roots. These roots seek moisture and nutrients in organic matter. They will wiggle their way into the sewer line and grow into a major clog. If you discover a tree root in your main sewer line, it may be time to contact the tree owner and have it removed. Otherwise, the problem can be remedied through the proper steps.

When the basement floor drain is backed up, it is likely caused by a blockage in the main sewer line. The blockage is in the drain line, but a plumber should use a high-tech camera snake to inspect it. If you can’t remove the blockage yourself, you may end up causing more damage and expense. A plumber will not only clear the clog but also make necessary repairs.

Installing a backwater valve

If you’re having problems with your basement floor drain backing up, you may want to consider installing a backwater control valve. Sewage can be a dangerous irritant and can flood the basement. Sewage flows from the house to a main sewer line beneath the street. When this pipe becomes plugged or overloaded, it backs up. The sewage is discharged out the lowest available drain, which is often the floor drain. Fortunately, you can prevent this problem with a backwater valve.

Sewage backups can occur when tree roots clog a sewer line. Older homes with clay or cast iron pipes may have deteriorated pipes. These pipes can easily back up with sewage. A backwater valve is an affordable and convenient solution to this problem. But you should only install a backwater valve where you’re sure it’s necessary. It’s also important to follow codes for backwater control valve installation.

If you’re looking for a backwater valve for your basement floor drain, you’ll need to make sure it’s plumbed separately from your existing plumbing. Make sure you install it at least 15 inches above the floor, as a backwater valve will be located several feet below the floor. To install a backwater control valve, you will need to route a separate piping line for each outlet.

Backwater valves are best installed by a plumbing professional, but they are often DIY-friendly as well. For existing homes, you will need a plumbing permit and will need to dig a hole through the concrete floor in the basement floor near the floor drain. Once there, your plumber will install the backwater control valve. Most of these valves have a clear lid that can be removed when cleaning it. They prevent the sewage from entering your basement by preventing it from flowing back up through the main sewer line.

While some municipalities require backwater control valves, others do not. In addition to the installation fee, you should expect to pay for labor. It can cost between $150 and $300 USD. You should also consider the cost of a plumbing service. The labor involved in installing a backwater control valve may exceed the valve’s cost. It will likely require some concrete removal and an excavation of the main sewer line.