Skip to Content

Eljer Whirlpool Tub Problems

Having trouble with your Eljer whirlpool tub? You’re not alone. More people are experiencing the same problems. In this article, you’ll learn about common problems with eljer whirlpool tubs. Read on for solutions to these problems and prevent further damage to your tub. In some cases, the problems may be as simple as clogged water jets. Other common problems include a faulty hot pump or air inlet.

clogged water jets

If you’re having Eljer whirlpool tub problems, clogged water jets could be the culprit. These jets in a tub can affect water pressure, and a clogged water jet can ruin your entire experience. Here are some ways to fix clogged water jets. First, remove the access panel from the tub. Next, check for any air that might be blocking the water jets.

If you’ve noticed debris in the jets, it may be because of the debris you tracked in from the job site. Spiders and mud daubers may have built a nest in the jets. The clog can be fixed manually with a wire, but it may not be worth the hassle. It might require professional repair. Insects and other bugs will also infest your Eljer whirlpool tub if you dump garbage in it.

If you notice black particles in your tub, the problem is most likely caused by algae. To clean it, use a mixture of 2 teaspoons of cascade dish soap and 1/2 cup bleach. Run the jets for 15 minutes and then drain the water. Repeat this process several times a week until the water jets are clean. Cleansers may be more effective, or you can call a plumber.

There are several ways to solve Eljer whirlpool tub problems caused by clogged water jets. You should clean the jets once a month and avoid using chemical cleaners. Then, you can use household ingredients such as baking soda and lemon juice to clean the jets. If you don’t have time to do all of these, you can try cleaning the jets yourself.

If your jetted tub is not turning on, you may have a problem with the electrical supply or wiring. If this is the case, check the power supply first to make sure the breaker is not tripped or the jets are working correctly. Next, make sure the power switch is fully turned on and that the “on” button has been pushed all the way.

Depending on your model of Eljer whirlpool tub, you might have to replace the clogged water jets. To replace a jet, you should first measure the length of the old jet and the diameter of the new one. You can take the measurements by looking online for the user manual or requesting a copy from the manufacturer. Then, you should remove all of the jets from your bathtub and then lay them on a flat surface.

faulty hot pump

Eljer whirlpool tub problems can result from a faulty hot-pump motor. The pump motor connects to a 1/4″ poly tubing that slides over a barbed nipple on the back of the pump housing. The pump’s high-speed motor can be controlled by pressing the white pneumatic pump control button on the tub rim. Occasionally, the connection is disconnected during installation.

Another reason your tub might not heat properly is a clogged jet. Sometimes, the problem is caused by debris from the construction site. Spiders and mud daubers may have built nests in the whirlpool tub’s pipes. To resolve a clog, you can manually clear the jets with a wire. If you have a jetted tub, don’t dump construction debris in it, as this will attract insects and other impurities.

When troubleshooting Eljer whirlpool tub problems related to faulty hot pump, it is vital to inspect the water piping of the pump. Faulty hot pumps can cause a hot tub to overheat or to leak. Check the hot pump’s GFCI protection to make sure the wiring is properly grounded. If you suspect a leak, inspect the wet end of the pump for mineral deposits. If you notice any of these signs, the pump may need repair or replacement.

If you suspect a faulty hot pump, you can test it by plugging the bathtub into the overflow drain. To test the connection, you should first plug the tub into the wall and insert a small rubber tube into the hole in the bottom of the switch. Finally, check the tub for leaks. Although they are rare, you should report these problems to the manufacturer. If the issue isn’t resolved, contact the manufacturer to get a replacement.

Another cause of faulty hot pumps is incorrect installation. Incorrect wiring of the hot pump can lead to a whirlpool’s malfunctioning hot pump. Fortunately, this problem is easy to diagnose. Follow the manufacturer’s instructions on replacing a defective hot pump. You may also want to check the hot pump thermostat. Failure to do so will cause the tub to malfunction.

Inspect the jets periodically for discoloration or debris buildup. Make sure the jets and bathtub surface are free from any dirt or debris. If this is the case, contact a professional. The manufacturer will replace or repair the part and repair the tub at no additional cost. This can help you save money in the long run. A faulty hot pump is the most common cause of Eljer whirlpool tub problems.

Faulty hot pump can cause the hot water to not reach the whirlpool bath jets. If this is the case, you can try replacing the jets using silicone caulk. To replace a damaged jet, unscrew the whirlpool tub intake cover. Use an old toothbrush and a bit of powdered laundry detergent to clean the intake cover.

faulty air inlet

The first step to troubleshooting a faulty air inlet in Eljer whipped tub is to download the owner’s manual for your model. Most manuals will also contain troubleshooting tips and advice for common problems. For clogged jets, you may need to clean the filter unit, which typically contains an air bleeder. Hair or debris may have clogged the water intake ports. A failing motor may have also tripped a circuit breaker or blown a capacitor.

Check the piping and power supply. You should see a plastic turn-screw on the tub’s edge. The air inlet is where the water jets get their air from, which is powered by the circulating pump. Once these are checked, the problem may be more severe. Then, check the air inlet and filter. If these are not clogged, you may have a faulty air inlet.