Skip to Content

How to Clear a Backing Up Washer Drain

If you have a backed-up washing machine drain, it may be due to a clog that is farther down the drainpipe. If you are unable to clear the clog with a plunger, consider buying a power auger, which uses a heavy-duty wire cable to drill through the clog. If you’ve tried everything else, here are some other tips for clearing your washing machine’s drain:


If your washing machine drain is backing up, the culprit may be soap residue buildup. This can be caused by soap residue from powdered detergents or homemade laundry soaps. Natural enzymes can help to clear the drain so that it will run smoothly and free of buildup. Detergents usually contain fillers and additives that don’t fully break down during the washing process. Eventually, these chemicals build up in the drainpipes, resulting in a clogged washer drain.

To clear your washing machine drain, you need to first remove any material that’s blocking the water flow. If the clog is mild, you can try a mix of vinegar and baking soda. This solution will fizz and dissolve the buildup. Then, add hot water and flush the solution down the drain. However, this solution won’t be effective if your drain is extremely stubborn.

One of the most effective ways to clear your washing machine drain is with enzymes. Enzymes are special chemicals that break down organic materials, allowing them to slide away. These products aren’t a miracle worker, however. They take time to work and should be used as an occasional maintenance step. Make sure you purchase a test pack to avoid having a chemical hazard, and wear a face mask while using them. Remember to vent the room before starting to use them, as the fumes from enzymes can easily seep into walls.

A homemade cleaning solution for a clogged washing machine can be purchased at any Home Improvement store. It can be used in the bathtub, kitchen sink, or washer drain. To get the best results, you should try using it several times, but only use enzymes if you’re certain the problem is due to the main waste pipe. If you’re dealing with a backup problem, make sure you stay safe and wear gloves when handling sewage. There are many dangerous pathogens in sewage, so use caution when dealing with it.

A clogged washing machine drain can be caused by a variety of reasons. Identifying the cause and preventing it from recurring is the best approach to solving the problem. If the problem is serious, a professional can install a drain cleaning system or fix it for you. For instance, it may be because your washing machine drain pipe is too small. If it is too small, the water can’t drain out fast enough.

Cleaning a clogged washing machine drain

When a clogged washing machine drain is backing up, the water pipe needs to be disconnected, so you can access the drain pipe. Clean the clog using household cleaning products or a hose. Most cleaning products are readily available at supermarkets, and they usually come with instructions for use. Some clogs are more difficult to clean than others, though, so be sure to read the label carefully.

One simple way to clean a clogged washing machine drain is by pouring a cup of baking soda down the drainpipe. You should leave this over the drainpipe for a few hours. You can also pour in one-fourth cup of table salt. This treatment should work for about four to five hours. If the clog persists, you should consider overnight treatment. The vinegar will help dissolve any remaining residue in the drainpipe.

If the clog is in the standpipe, then it’s likely that the machine’s drainpipe is clogged. To figure out where the clog is in the drainpipe, try to monitor the exact time the water starts backing up. If you’re not sure, you can estimate the timeframe by measuring the time it takes for the water to overflow. You can then use a pipe cleaner to clear the clog if it’s near the beginning of the drainpipe. However, if the clog is further down the pipe, you’ll need to call a plumber.

When using the drain snake, it’s important to carefully locate the source of the clog. It’s a common place for the clogging. This extra hose is the primary connection between the washing machine unit and the home plumbing system. To remove the clog, disconnect the drainage hose and insert the drain snake. The snake should latch on to any pieces of gunk that are clogging the pipe. When the drain snake is clear, insert the drainage hose back into the machine’s drain pipe.

Inspect the machine’s drainage system carefully for gunk and grease buildup. During regular washing cycles, pet hair, lint, and clothing fibers may accumulate on the drain pipe walls. When these particles accumulate, they prevent water from draining properly. This can also lead to considerable plumbing problems. If you can’t locate the source of the clog, consult a plumbing expert.

Using an anti-siphon clip

In some cases, a clogged washer drain may be the result of a leaky or damaged hose. You can use an anti-siphon clip to fix the problem by attaching a hose to the back of the machine. A high loop is easy to install, but you may need to drill holes in your sink or counter top. Some kitchen sinks come with a hole already drilled in the counter top. If you have an old kitchen sink, you can also use an air gap device.

To prevent this, make sure that the drainpipe is at least 30 inches from the floor. You may have to raise the height of the drainpipe a few inches, but many washing machines require a height of 36 to 96 inches. If you’re unable to raise the drainpipe to this height, you can install an anti-siphon clip.

First, try cleaning the hose. Usually, this will solve the problem. If not, try using a drain snake, which works by pushing one end of the snake into the clogged pipe. You can also use a garden hose to clear up the drain pipe. Using a hose in the standpipe may not work because it’s filled with debris, but it will confirm that the clogged pipe is actually in the standpipe.

If the washing machine drain is backed up, you’re most likely dealing with a plumbing issue. Identifying the cause will help you solve the problem and prevent future issues. Make sure your drain pipes are regularly maintained to prevent clogs and backups. Another option is to hire a professional drainage system installation specialist. This option is more expensive than a professional drain snake.

Using a mesh lint catcher

Washing machines are the most common culprits when it comes to clogged sewer lines. A backed-up washer drain can even submerge the basement floor. But there’s an easy solution! Install a mesh lint catcher on your washing machine’s drain hose. This self-explanatory device attaches to the discharge hose without altering its size or shape.

Lint and hair often cause sewer backups. When they accumulate in the sewer, this lint can get into the mainline drain pipe, where it can clog. By installing a flint trap in your washer’s drain hose, you can prevent a sewer backup by preventing small bits of fabric and hair from accessing the sewer line.

A mesh lint catcher can help prevent sewer overflows by collecting lint that would otherwise be deposited on the bottom of the pipe. If the mesh lint catcher is not functional, you can simply replace it every month. This will remind you to use a drain pipe enzyme that targets lint. These enzymes work well against the soap buildup.

Lint traps are an inexpensive, effective way to protect the drain from clogging. However, they can also be expensive to replace. That’s why choosing a reusable mesh lint catcher is a better option. It’s reusable, easy to install, and can protect your washing machine’s drain. This simple solution will prevent your washer from backing up by more than half.

There are several different types of lint traps available for washing machines. Depending on your budget, you can purchase a plastic one from a hardware store or DIY project. Or you can simply use an old nylon stocking. Just make sure to replace it when it’s full. A better mesh lint trap is the Sioux Chief Lint Trapper, which you can find online or in some home centers.

Using a mesh lint catcher is a simple way to prevent a backed-up washer drain. A lint trap is an essential part of a washing machine. It prevents debris from reaching the drain pipe and flooding your laundry room. Lint traps can also help prevent slow drainage, which can lead to expensive repairs.