Skip to Content

How to Unclog a Clogged Washer Drain Pipe

If you want to unclog a plugged washing machine drain pipe, there are a few things you can do. First, you should detach the tubing from the washing machine so you can access the pipe. Next, mix a solution according to the manufacturer’s instructions. Pour it into the drain, and leave it for the recommended time. You can then run the washing machine to see if the blockage has been removed. If not, you may need to use a plumber’s snake to clear the drain.

Remove a clogged drain pipe from a washing machine

To clear a clogged drain pipe, you’ll first need to remove the washing machine from its pedestal and move it to a clean area. Once you’ve moved the machine, you can access the drain pipe, usually located between the hot and cold water knobs. To clear the drain, insert a drain snake into the pipe and feed it through the drain until it meets resistance. Turn the drain snake handle clockwise and continue until all pieces of the blockage are removed. To clean your machine’s drainage pipe, be sure to use a detergent-free laundry soap. After cleaning the drain pipe, put the drain hose back into the machine.

A washing machine drain pipe can clog for various reasons. The most common reason is improperly sized drainpipes. Small fabric fibers are routinely flushed through the system and can cause blockages. If you’re experiencing a slow drain, a clogged drainpipe may be further down the drain pipe and beyond the drain trap. If this is the case, a medium drain snake will help you clear the clog through the cleanout.

The first step to clearing a clogged drain pipe is to remove the additional drain hose. This is where the majority of the clogs occur. Next, use a drain hose snake to clean the clog. The snake will latch onto the debris and twist itself out of the pipe. Once the snake has gone through all of the blockages, you can test the drain pipe by pouring water through it.

If the washing machine is not giving you any error messages, it may be a problem with the drain. Check the machine’s manual to determine what may be the problem. You may need to contact a repair service or call a plumber, depending on the type of clog. However, if you are skilled at DIY plumbing, you can easily clear a clogged drain pipe.

Once you’ve cleared the clog, the next step is to try and remove the secondary drain hose, which connects to the washing machine. You may have to dismantle the washing machine to reach the drain pipe. A clogged drain pipe will impede the flow of water. If you can’t remove the secondary drain hose, you can use a plumbing snake to clear the clog.

Unclog a clogged drain pipe with baking soda and vinegar

For stubborn messes, try a mixture of baking soda and vinegar. Baking soda and vinegar are acid and base, so they react together to loosen the clog. To start, pour about half a cup of baking soda down the drain. Next, add one cup of vinegar. Let the solution sit for five to ten minutes. Close the drain plug after five to ten minutes. Repeat the process as many times as necessary to clear the clog.

The vinegar and baking soda mixture is effective against a plugged washer drain pipe by dissolving the FOG deposits. The reaction of the two substances generates carbon dioxide and water, which bubble through the liquid in the pipe. The carbon dioxide dissolving power of the mixture helps break up clog-causing materials and clear the pipe. Meanwhile, the boiling water will soften greasy and fatty buildup and create pressure, forcing it out.

If the clog is deeper than the trap, you may need to remove the drain pipe. Alternatively, you can use boiling water and baking soda to unclog the drain. Make sure to follow the directions exactly as stated in the instructions. After several hours, add a quarter cup of table salt to the mixture. The mixture should stay in the drain pipe for at least an hour before you see the results. If the clog is still stubborn, you can use vinegar and boiling water.

Another way to clear a plugged washing machine drain is to pour a cup of baking soda and a quarter cup of table salt into the pipe. Then, leave the mixture for up to four to five hours to ensure the mixture has time to work. If you’re patient, the mixture may be effective and can clear the most stubborn clogs. If you’re willing to put in the time and effort to clean the drain, this home remedy is worth the effort.

If all else fails, you can make a homemade solution of baking soda and vinegar. You can pour the mixture down the drain whenever the water drains slowly and remove the clog. This solution is more powerful than boiling water alone and can work in stubborn clogs. If this method doesn’t work, call a plumber to help you clear your drain. Soap and vinegar are both effective, but it may be better to use boiling water.

Unclog a clogged drain pipe with a drain snake

Before you can use a drain snake to unclog a plugged washer drain pipe, you need to know how to clear the trap in the back of your machine. Sometimes, a clogged drain backs up beyond the trap. When this happens, you’ll need to use a drain snake to unclog the pipe. Because drain snakes aren’t available for sale, you may have to rent one from a home improvement store.

A drain auger is a steel wire with a handle on one end. Like a plunger, it works by pushing it into the drain. As it goes deeper, it will eventually catch and remove the clog. For thicker blockages, a plumber’s snake can be attached to a drill. Once the snake is attached to a drain, pull it counterclockwise and clockwise. If you’re having trouble getting it through, you can try rotating the snake with one hand while pulling it back out.

First, unplug your washing machine. This will prevent any unnecessary damage to your hoses. After you’ve unplugged the washing machine, use boiling water and baking soda to unclog the drain. Boiling water should also work if the clog is deeper than the trap. If this method does not work, you can try using a drain snake to unclog a clogged washer drain pipe.

When the clog is small, the hand-operated snake can clear the hose on its own. If the water is taking a long time to stop, however, the problem may be more extensive and requires a plumber. To avoid a costly plumbing bill, call a plumber to check your plumbing system. If the clogged pipe is deeper than the hose, you can use a long drain snake to reach it.

If the clog is too severe to remove by hand, you can use a pressure washer with a sewer jet attachment. However, if you’re using a pressure washer with a hose, you may want to hire a professional plumber to do the work. Professional plumbers have the experience, training, and insurance to solve the clog. Plus, their work is guaranteed, so you’re less likely to end up with a mess.

Check for a leaky drain hose

One of the first steps in clearing a clogged washing machine drain pipe is to check for a leaky drain hose. If you’re able to remove the clogged hose, the blockage is likely farther down the pipe. A chemical drain cleaner, heavy-duty drain auger, or plumbing snake can be used to unclog the hose. If the hose is not visible, unplug the washer before cleaning it.

If you find that the drain hose is clogged, try blowing through it. If there are no obstructions, then it’s the pump that’s likely to be the culprit. A poorly kinked or worn drain hose can affect the pump’s performance, so it’s a good idea to replace the hose. Otherwise, you’ll have to deal with the leaky washing machine and the water it produces.

Whenever a clogged washer drain pipe is causing water to overflow, it’s time to call a plumber. The plumber will be able to diagnose the problem and provide a solution. If the drain is clogged, you may be using an improperly sized drain pipe or a kinked drain hose. If you can’t locate a leak, you can call a plumber to inspect your sewer and drain lines.

A power drain snake can easily clear a small clog in a standpipe. If the drain pipe is large enough to accommodate a medium-sized drain snake, a large drain snake can help clear a clog deeper into the drainpipe. A long drain snake can reach deep pipes and remove the clog without compromising the flow of water.

If the clogged drain pipe is due to a leaky drain hose, the next step is to remove the temporary plastic plug from the washing machine. The hose is attached to the drain valve on the back of the washing machine. Alternatively, you can remove it and reattach it. Be sure to check the connections for loose connectors or damage before attempting to remove the clogged drain hose.