The average cost of hot water heater installation varies depending on the type and size of water heater you need, where you need it installed and a variety of other factors. The installation process is most expensive when it is done in an obstructed location. The labor cost for this type of installation can range from $400 to $1,000, while power venting will increase the overall cost by at least $500. Direct venting will add another $500 to $1,000 to the cost.
Installing an electric tank-style water heater
The average cost to install an electric tank-style water heater varies depending on size. For example, an 80-gallon unit can be very expensive to heat with electricity alone. However, hybrid units are a good choice because they provide on-demand hot water while also utilizing a heat pump to keep the costs down. In addition, larger tanks are generally only required for large freestanding bathtubs and performance shower systems.
If your heater is old, the cost will likely be higher. An electric tank-style water heater typically costs $285 plus an additional $50 for parts. A new anode rod will last for up to five years, and it will cost approximately $50 to replace. If you don’t have the knowledge or experience to replace the anode rod yourself, you can also hire a plumber. A plumber may charge about $250-300.
Electric tank-style water heaters are less expensive, but aren’t free of complications. A tankless unit will run you $500 to $1,500, but the cost will depend on how you want it installed. It may require an electrician to add a new electrical service near the water heater or install a new circuit breaker in the electrical panel. These additional costs can add up to $900 or more.
Installing a gas tank-style water heater
While the average cost of installing a gas tank-style hot water heater is less than that of a conventional electric heater, there are other costs to consider. Electrical and plumbing professionals typically charge by the hour, and the work can range from $45 to $150 per hour. Additional expenses may include new wiring and an expansion tank. Plumbing professionals may be required to install an enclosure or drywall, and carpentry work may also be required.
The average cost of installing a gas water heater depends on size. Most tank-style models are 40 gallons. While the larger sizes tend to cost more, the more energy-efficient they are. Moreover, they can work even when the power goes out. However, it’s important to note that a larger water heater will likely cost more than a smaller model. If there are more than two people in the household, a 40-gallon tank may be sufficient. For households with more than five people, a 60 to 80-gallon tank may be required.
The average cost of installing a gas tank-style hot water heater can vary greatly depending on where you live and which model you choose. Depending on the size of your home, you’ll need to decide whether a 30-40 gallon model or a 50-60 gallon unit will suit your needs. Ensure that you choose a model with the highest energy efficiency possible, as this will save you money in the long run. If your gas tank-style water heater starts to show signs of deterioration, it may be time to replace it with a new one.
Moving a tank-style water heater
Whether you’re moving across the country or just need to update the style of your home, there are several tips to consider when moving a tank-style water heater. First, make sure you have enough room for the pump and a minimum of eight feet of vertical clearance. A tank-style water heater is also more efficient, using 60 percent less electricity than a conventional one. Just make sure you clean it regularly, since sediment can accumulate and ruin it.
Another important consideration when moving a tank-style water heater is the size of the tank. A storage tank is often more than two feet tall and two feet wide. If you have a basement, this is not a problem, but if not, you may need to use your closet space to store it. Newer models are larger, which means you’ll need more space for the tank. Finally, if you plan to relocate the water heater, make sure it’s adequately insulated.
To avoid damage to the unit, make sure to move it from a room to another. You may need to reroute water, gas, and vent ducting lines, and that can be a costly and time-consuming task. If you’re unsure, consider hiring a professional. You may also need a dolly. Remember to secure the tank to a dolly so you don’t have to lift it yourself.
Converting from electric to gas
If you are thinking of switching your hot water heater from electric to gas, you’ll likely have to upgrade your home’s electrical panel. This is because gas is much cheaper than electricity. In some areas, an electric water heater won’t cut it. Additionally, electricity is often unreliable. It’s best to hire a licensed electrician to perform the work. Here’s a basic guide to converting from electric to gas:
Before deciding on a new water heater, you’ll need to determine its energy efficiency. An electric water heater’s energy factor (EF) measures how efficiently it uses fuel. A higher EF number indicates a more energy-efficient model. However, gas and electric water heater efficiency tends to be similar, despite some hybrid heat pump units. But if you are planning to convert your current water heater, consider hiring a Phoenix plumber to help you make the switch.
The price of an electric water heater installation can range from $500 to $1,800. Permit fees and carpentry work are typically additional costs. Expanding the gas line can cost an additional $40 to $350, but this is necessary in many new homes. Converting from electric to gas hot water heater installation can cost upwards of $2,300, and can also be costly if you have an existing gas line in your home.
Electric tank-style water heaters vs. gas tank-style water heaters
There are a few things to consider when choosing an electric tank-style water heater. First, there’s the energy factor. This rating measures the efficiency of insulated tanks and gas-powered tank-style units. Electric models have higher EF ratings than gas ones, which makes them more expensive to run. Also, gas models typically require more maintenance and may not last as long as an electric model.
Another thing to consider when choosing an electric tank-style water heater is the FHR (first-hour-reward) rating. FHR is the amount of hot water a water heater will heat in the first hour after the tank is filled. Electric tank-style water heaters are more efficient, but may take up to twice as long to heat water compared to their gas counterparts. However, electric tank-style models are still impressive for smaller homes.
The storage-tank type of water heaters are the most common in homes. They typically hold 30 to 50 gallons of water and heat it before releasing it through pipes. As the hot water drains from the storage tank, replacement cold water fills the tank. There are many different types of storage water heaters available. Electric and gas tank-style water heaters are generally less expensive, although natural gas units cost more upfront. Gas tanks use 10 percent less energy than electric units, which can result in higher savings over time. A typical tank water heater can last up to 15 years.
Cost to convert from electric to gas
The cost to convert from an electrical to a gas hot water heater installation depends on how much work needs to be done. The replacement of a water heater can cost from $500 to $1,800, and this estimate includes carpentry and permit fees. Additional costs include a vent stack and additional wiring. Electrical wiring and gas line extension costs can add up to $500. You may also need a dedicated circuit for an electric water heater, which adds to the overall cost of the project.
There are several things to consider before deciding on the type of fuel for your water heater. Make sure you select a plumber who specializes in this type of system. A qualified plumber will have the experience necessary to install a unit. While not every contractor can install this type of unit, ask about their experience and license to ensure a successful installation. Some plumbing projects require special expertise and should only be done by a licensed professional.
The installation process may require the help of an electrician. Depending on the size of the heater, the electrician may have to install an electrical panel to plug it into. Some heaters can simply plug into the wall, but larger ones may require a dedicated circuit. Obviously, this will increase the overall cost of the project. However, the savings can be worth the additional expense. In addition to paying for the installation itself, you will also be paying for maintenance for the first three years.