Skip to Content

Subaru Check Engine Light Flashing Cruise Control – How to Fix It Yourself

If your Subaru Check Engine Light keeps flashing and is not responding to your commands, there are a few common reasons why this happens. Among these reasons are corroded connectors, Corrosive fluid, and a failed catalytic converter. To fix this issue yourself, we have provided a quick guide below. If your Subaru has a similar problem, you can follow these tips. These solutions are simple, inexpensive, and effective.

corroded connectors

The most likely cause of your Subaru’s check engine light flashing cruise control is corroded connectors in your vehicle’s computer. This problem can affect various car systems, including cruise control, ABS, and traction control. To clear the light, you need to diagnose the problem. To determine which one is causing the problem, look under the hood to see if any of these systems are malfunctioning.

Another possible cause of your Subaru’s check engine light flashing cruise control may be a loose gas cap. This issue can cause a number of symptoms, including engine shakes, code P0457, and the need to replace spark plugs. If the fault is with the engine, a diagnostic tool such as an OBD-II scanner can help. The scanner plugs into the OBD-II port in your dashboard. When you turn on the ignition, but don’t start the car, the scanner will read stored fault codes.

Another common cause for your Subaru check engine light is corroded connectors. A corroded connector can affect the connection between the throttle and vacuum actuator, which controls the cruise control cable according to the settings on the dashboard. A faulty sensor could make it impossible to turn on or off the cruise control. However, if the connectors are intact, the light will continue to illuminate.

If none of these solutions work, try a continuity test on the wiring harness. Depending on what the error code is, you might have to replace the entire circuit board. Then, compare the results to factory specifications. If they’re not, it’s time to replace the cruise control switch. If you have trouble with the cruise control switch, you can also try a resistance test on the buttons of the cruise control.

Catalytic converter failure

If your Subaru has a code that says “catalytic converter below threshold” and is flashing your check engine light, you may have a catalytic conversion problem. You should replace it when it reaches 200K miles. A catalytic converter is designed to last for about two decades. A failing catalytic converter can cause your engine to misfire, leading to a stalling problem. If you see this code, make sure to take it to a Subaru mechanic. They can diagnose and replace your catalytic converter for you, saving you time and money.

Another cause for the check engine light to flash in your Subaru is a malfunctioning one-way fuel valve. When the valve malfunctions, the catalytic converter may not be able to properly burn fuel, resulting in misfires. It could be caused by a malfunctioning fuel injector, a problem with the oxygen sensor, or a problem with the one-way fuel valve. While this method does clear diagnostic codes, it doesn’t fix the issue. If you don’t fix the problem, the check engine light will come back.

Other causes of the check engine light in your Subaru include the cruise control deactivation switch or a malfunctioning oxygen sensor. The malfunctioning sensor can lead to your car not working properly or flashing its speedometer. A new exhaust system will restore the ability of the car’s oxygen measuring systems. It may be necessary to replace the entire exhaust system in order to fix the check engine light.

If the check engine light is flashing and causing the cruise control to stop working, the culprit is most likely the catalytic converter. Changing the engine will cost around $4,000, so replacing the catalytic converter could save you a few hundred dollars. If the fault is more widespread, however, you might need to replace the entire engine. Then, the check engine light will flash while accelerating.

Speed sensor failure

If your Subaru check engine light is flashing, it may be due to a faulty cruise control speed sensor or a faulty VVL pressure switch. The code will also indicate a rough idle. It may also be triggered by low oil levels or sludged oil. To fix the problem, visit a Subaru dealer or service center. To ensure your safety, it is important to keep your vehicle inspected regularly.

A malfunctioning catalytic converter is another common cause of the check engine light on a Subaru. If the sensor is faulty, the car will not be able to use cruise control. This is a costly repair that can be expensive. If you’re not sure if the problem is the catalytic converter, you can consult a Subaru mechanic to check the code. Fortunately, most Subaru mechanics offer to come to your location for free.

Regardless of the cause, you should avoid using the cruise control until the problem is resolved. If the problem cannot be fixed by a DIY fix, take your Subaru to a mechanic for diagnosis. You can also check the codes using the OBDII port. If you do not feel confident enough, you can also visit a Subaru dealership service center to have the problem diagnosed and repaired. If you’re a complete amateur, you should consider using the Jerry app to review your car insurance policy.

Other reasons why your Subaru check engine light may be flashing include faulty plug wires. The plug wires supply the voltage needed to ignite the spark plugs, which in turn makes the engine run. If the plug wires malfunction, you’ll be short of power and the check engine light will illuminate to warn you of low power. The check engine light may also be accompanied by a reduced speed.

Corrosive fluid

The cruise control in your Subaru may be flashing in addition to your Subaru check engine light. It may be a sign that your vehicle has a problem with its fuel tank sensor. In such a case, you should look at the fuel cap and tighten it to three clicks. The light should then go off within 3 warm up and cool down cycles. You may also be experiencing leakage of coolant or oil, but these are all easily rectified.

A damaged fuse, a worn-out gas cap, or a faulty brake pedal could be the cause of your car’s cruise control light. It may even be a sign of a more serious problem. Either way, it’s important to get your vehicle fixed as soon as possible. However, if you can’t find a repair shop that can fix the problem, you may need to tow your car to a repair shop.

If you aren’t comfortable diagnosing your Subaru’s problem yourself, seek the help of a mechanic. The Subaru Select Monitor device will upload new software and resolve the problem. A few parts may also be damaged, but an experienced mechanic can determine which ones are the culprits. If you can’t find a reliable mechanic, consider visiting a Subaru dealer for a comprehensive diagnostic.

The best way to diagnose the issue quickly is to check the coolant. The Subaru cooling system uses phosphate, a non-anime liquid that is specifically designed for Subaru’s aluminum radiators. If the fluid is leaking, the vehicle’s temperature may rise. If it is, it may require a costly vehicle recall. However, many owners of Subaru vehicles have sworn never to buy another Subaru again.

Head gasket failure

If you’ve noticed that your Subaru check engine light is flashing, this problem may be related to a failed head gasket. The good news is that this issue is easy to fix – as long as you catch it early! Check the coolant and cylinder fluid levels as well. Changing these can prevent more expensive repairs, including replacing the head gasket. The best solution is to find a professional mechanic who has experience working on Subarus.

If the Check Engine Light is flashing and you’ve performed a full service, your car will have a new engine code that will tell you the problem. You can use an electronic scan tool to read this code. You can buy a do-it-yourself version of a code reader. While it’s not a substitute for professional diagnostics, this is an inexpensive, easy-to-use tool for diagnosing the problem.

Another common problem is a failed head gasket. Head gasket failures can cause the check engine light to appear when the engine is running in limp mode. In some cases, the head gasket may not be the cause. Other problems may be related to the car’s fuel injector, emissions control systems, or oxygen sensors. If your Subaru’s check engine light is flashing, you should immediately visit a mechanic. The good news is that you can reset the check engine light using an on-board diagnostic scanner or code reader.

If the head gasket of your Subaru is failing, you should get it checked immediately. The company needs to recall affected vehicles as soon as possible. The defect is widespread, and the fix is simple: replace the head gasket. In the meantime, your car may suffer severe damage. The Subaru check engine light flashing on cruise control may be the first sign of a head gasket problem. As a result, you should avoid buying a Subaru unless you’re sure that your vehicle will work properly.